Iogear GMFPSU22W6 Guide d'installation

1GMFPSU22W6PART NO. M0389InstallationInstallation GuideUSB 2.0 Hi-Speed 2-Port Multifunction Print and Storage Server User Manual

1011Software InstallationInsert the Software CD into your computer. A splash screen should appear with a menu of options. Click on the words Install

1011Click Next to continue the installation wizard.

1213Type your name and organization to personalize the installation of the Control Center software, then click Next to continue.

1213Click Change… if you would like to install the software to somewhere besides the default location, then click Next to continue.

1415Click Install and wait a moment for the Control Center software to nish loading.

1415Click Finish to exit the install wizard and launch the Control Center software for the rst time.

1617If you have a software rewall you may be alerted that the Control Center is being blocked. Make sure that you unblock the Control Center or you

1617After a moment your print server should appear in the server list. Click the server name once and any attached devices should be listed be-low it

1819You may wish to manually assign an IP address to the server in some cases. For example, if you do not have a DHCP server on the network. Most us

1819At the prompt, enter the administrator username (default: admin) and password (default: admin).Conguring the Server IP

3

2021After you have logged in successfully, select the TCP/IP tab. Here you may select Static IP and manually congure all network settings for the se

2021Printer/Fax/Scanner Setup (Virtual USB)Your print server supports a technology called Virtual USB in addition to more traditional print server por

2223Your printer should be detected and installed au-tomatically at this point. You can repeat this setup procedure on all your computers as needed.

2223Storage Setup (Windows File Sharing/SMB)Storage devices attached to your server are ac-cessible through Windows File Sharing and FTP protocols. F

2425Storage Setup (Virtual USB)To gain full control of NTFS disks you will need to use the Virtual USB mode for storage devices. In this mode only on

2425To turn on Virtual USB mode, open the Control Center software and double click on the server name in the list. Enter the administra-tor username

2627Once this is done, you may connect or discon-nect from storage devices in the same way you would a printer. Simply open the Control Center interf

2627When you are done using the drive, click the Safely Remove Hardware icon in the tray area by your clock to prevent further communication with the

2829Restore Factory DefaultsIf you are having difculty nding or connecting to your print server using the Control Center software due to network iss

2829Should you require any technical assistance, call toll-free: 866-9-IOGEAR (866-946-4327) or visit our website at http://www.iogear.com for the lat

3Introduction Thank you for purchasing the IOGEAR GMFPSU22W6 2 Port USB 2.0 Multifunction Print and Storage Server (hereafter referred to as “server”)

3031Radio & TV Interference StatementWARNING!!! This equipment generates, uses and can radiate radio frequency energy and, if not installed and u

3031Limited WarrantyIN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDEN-TAL OR CONSEQUENTIAL DAMAGES RESULTING FROM

© 2007 IOGEAR, INC.FUNIOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high techn

45About this Manual This manual provides introductory information as well as detailed instructions on how to set up and man-age the IOGEAR GMFPSU22W6

45Table of Contents Package Contents 6Physical Description 7Hardware Installation 9Software Installation 10Conguring the Server IP 18Printer/Fax/Sc

67Package Contents Verify that nothing is missing from the package by using the checklist below. Please contact your dealer if anything is missing or

67Physical Description 1. Power Adaptor Connector: DC IN 12V/1A adapter 2. Init Button: restores all settings to default values 3. Ethernet Conne

89Indicator Behavior Description Power Lit Power On Not lit Power off/System error Link Lit Network connected Not Lit No physical connection to

89Hardware Installation Make sure that your USB devices are switched off and that the server’s power adapter is disconnected. Connect the print and/o