Iogear USB PDA/ Serial Adapter GUC232A Manuel d'utilisateur télécharger pdf

System Requirements

• Mac OS 8.6 or greater

• Windows 98, 2000, ME

• Available USB port on system or USB hub

Installation

Installing the Adapter (PC)

With the computer on, plug the USB side of the adapter

into your computer or hub’s USB port. Once the USB

connector is inserted into the PC, the "New Hardware

Wizard" should appear, click NEXT to continue. A new

dialog box should appear, make sure the default

A new dialog box should appear, make sure the default

setting is selected ("Search for the best drivers for your

device") and click NEXT to continue. Insert the

installation CD into your computer's CD-ROM

drive. In the next dialog box, select the CD ROM drive

and click "NEXT" to continue.

Insert the installation CD into your computer’s CD-ROM

drive. In the next dialog box, select the CD ROM drive

and click NEXT to continue.

In the ready to install... dialog box that comes up. Click

on "Next" to continue. Files are now copied to our hard

disk.

Windows will now finish the installation process.

Checking The Installation (PC)

Open the My computer folder.

Open the Control Panel folder.

Open the system folder.

Click on the Device Manager tab at the top

of the dialog box.

Click on the plus sign in front of the Universal

Serial Bus Controller heading to see the

Universal Serial Bus Controller listing. If the

installation completed successfully, you should

see an entry of our USB Serial Port in the listing.

Model G-UC232A Function Diagram

Computer

USB PDA/SERIAL Adapter

Serial Devices

Uninstalling the Driver (PC)

Open the System folder: (My Computer ->

Control Panel -> System)

Click on the Device Manager tab at the top of

the dialog box

Click on the plus sign in front of the Universal

Serial Bus Controller heading to see the

Universal Serial Bus Controller listing.

Select our USB Serial Port in the listing.

Click on the Remove button.

Peripheral Installation: (PC)

This procedure only occurs the first time you connect your

peripherals. If your peripheral was previously connected and

configured for the RS-232 (COM) port, after you perform the

Adapter Installation and click on Finish, the driver will detect it

and install it automatically.

Under Windows 2000, if you connect a modem, you must specify

it as a standard Modem.

With the computer on and the USB Serial Adapter plugged into

the computer or hub’s USB port, connect the peripheral into the

DB-9 connector on the USB PDA Adapter. Turn the peripheral on.

Follow the Installation Wizard's on-screen instructions to complete

the installation.

NOTE:

Overview

Universal Serial Bus (USB) technology has emerged in

response to the proliferation of external peripheral devices

(i.e. scanners, digital cameras, removable drives, and etc.),

that are increasingly being connected to the latest

generation of computers. USB behaves in a similar

fashion to conventional bus ports (i.e., serial, parallel, and

PS/2), except, it does not require any IRQ's. This allows

for multiple devices to be connected to the system thus

eliminating any IRQ conflicts.

The USB PDA/Serial Adapter (GUC232A) provides you

with an external serial (DB-9 male) Plug-N-Play connection

for use with computers, notebooks, and hand held

computing devices that support USB. The PDA/USB Serial

Adapter has a standard type A USB plug.

This USB PDA/Serial Adapter provides PDAs, digital

cameras, modems, and ISDN terminal adapters with high

quality serial connections at a data transfer rate of over

230Kbps. This makes the USB interface transparent to

serial peripherals, allowing them to easily interface with

USB computers. This eliminates the setup hassle found

with traditional serial port. This device also supports

energy saving suspend and resume operations.

Note: This adapter installs as a virtual port driver on

Com3. As such it does not support devices, such as

serial mice that require an IRQ number or IO address.

Features:

• USB Plug-N-Play connectivity

• Full Compliance with USB specification v1.1

• Works with cellular phones, PDAs, digital cameras,

modems and ISDN terminal adapters

• Easy Installation

• Support the RS 232 Serial interface

• Provides a 96 byte buffer for each upstream and

downstream data transfer

• Supports automatic handshake mode

• Supports Remote wakeup and power management

• Frees your RS-232 ports for other uses

• No IRQ required

INSTALLATION MANUAL FOR GUC232A

USB PDA/SERIAL ADAPTER

IOGEAR • 23 Hubble Drive • Irvine, CA 92618 •P: 888-999-2836 •Web-site: http://www.iogear.com •Technical Support: [email protected] •Product Information: [email protected] • IOGEAR • 23 Hubble Drive • Irvine, CA 92618 •P: 888-999-2836 •Web-site: http://www.iogear.com •Technical Support: support

Trouble Shooting (Mac & PC)

Please visit www.iogear.com for the latest drivers

and technical information.

Try unplugging and replugging the devise if it is not

immediately recognized upon start up.

•

Trouble Shooting (PC only)

If the installation fails, go to the "Device Manager" and

delete "USB Composite Device" from the USB device

list. Once removed, follow the installation guide to install

the USB Serial Adapter again.

If the "New Hardware Wizard" is not able to recognize

the drivers from the Installation CD, try installing the

drivers using "Add/Remove Programs" from the control

panel.

•

Installing the Adapter (Mac)

Insert the installation CD that came with the unit.

Double click on the (.sit) for or installer within the Mac folder.

Make sure the extensions find their way to the Extension Folder.

The installer should place all extensions necessary into your

Macs extension folder.

Restart your computer

Plug the GUC232A into the computer or hubs USB port.

Peripheral Installation: (Mac)

With the computer on, and the USB Serial Adapter plugged

into the computer or hub’s USB port, connect the peripheral

to the DB-9 connector on the USB PDA Adapter. Turn the

peripheral on.

Restart if necessary

Follow normal peripheral operations for installation and use.

PC Installation

Mac Installation

USB PDA/SERIAL ADAPTER 1

Résumé du contenu

Page 1 - USB PDA/SERIAL ADAPTER

System Requirements• Mac OS 8.6 or greater• Windows 98, 2000, ME• Available USB port on system or USB hubInstallationInstalling the Adapter (PC)With t

Commentaires sur ces manuels

Pas de commentaire

Iogear USB PDA/ Serial Adapter GUC232A Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Iogear USB PDA/ Serial Adapter GUC232A. IOGear USB PDA/ Serial Adapter GUC232A User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Iogear USB PDA/ Serial Adapter GUC232A