1InstallationInstallation GuideSolar Power Bluetooth Hands-free Car KitGBHFK231
1011Using solar power Place the Solar Power Bluetooth 1. Car Kit under direct sunlight exposure with 45 degree angle, and have the solar panel facing
1011Recommended Way of Using Your Car KitOn the sun-visorSlide the Car Kit into the sun-visor 1. mount.Place the Car Kit with sun-visor 2. mount onto
1213Mounting the Car Kit on the windshield IMPORTANT NOTE: Before start using the Windshield Mount on your windshield, check the state and local laws
1213Take the Car Kit off the windshield 1. mount.Clean the surface of your windshield 2. where you want to mount the windshield mount.
1415Push and hold the windshield 3. mount against the windshield until the windshield mount is securely attached to the windshield. Note: If you have
1415Slide your Car Kit back into the 4. windshield mount and now you can charge the Car Kit battery with solar energy.
1617Connect Car Kit to your Bluetooth enabled cellular phoneTurn on the Bluetooth connec-1. tion on your phone and enable the pairing mode of the Blue
1617Note: If the pairing process can not be completed within 2 minutes after pairing mode is activated, the Car Kit will power off automatically. Ple
1819Operating the Car Kit with Two Bluetooth enabled phonesActivate multi-point connection The default setting of Car Kit’s multi-point connection is
1819Pair Two Bluetooth enabled cellular phones Before begin to pair two Bluetooth enabled phones with the Car Kit, rst you 1. need to make sure to ac
23Package Content 4Requirements 5Device Overview 6Charging Your Car Kit 7Recommended Way of Using Your Car Kit 11Connect Car Kit to your Bluetooth ena
2021Note: If the Car Kit does not connect back to the rst phone or having problem staying connected with any one of the two phones, try to power cycl
2021Rejecting call from the second phoneWhen a new call comes in on the second phone, press and hold MFB button for 3 seconds to reject the call from
2223Using your Car KitPower OnLong press the MFB button for 4 seconds until you hear a short beep. The BLUE LED will ash 5 times and the Car Kit wil
2223Voice DialIf you cellular phone voice dialing is enabled, short press the MFB button under standby mode and say the voice tag after hearing a beep
2425Adjusting the VolumePress the “+” or “-“ button repeatedly until you reach the desired volume level. MuteShort press the Mute button during a cal
2425Transferring Call from phone to Car KitPress Both “+” and “-“ to direct the call back from cellular phone back to the Car Kit.
2627LED Indication Device StatusLED StatusPower OffLED OffPowering OnBLUE LED ash once every 3 secondsPowering OffRED LED ash onceStandby ModeBLUE L
2627Device StatusLED StatusCall in ProgressBLUE LED ash once every 6 seconds Pairing ModeRED and BLUE LED ash alternatively Charging in ProgressRED
2829Restore to Default SettingsWhen the Car Kit is on and in standby mode, press and hold both “+” and “-“ 1. buttons for 10 seconds until the BLUE an
282915.21You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority
23LED Indication 26Restore to Default Settings 28Federal Communications Commission (FCC) Statement 29CE Statement 32Limited Warranty 33Contact 34
3031guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
3031THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. this device may not cause interferenc
3233CE StatementThis device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law
3233IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULT-ING FROM THE USE OF THE
3435IOGEAR19641 Da VinciFoothill Ranch, CA 92610Visit us at: www.iogear.comContact© 2009 IOGEAR® Part No. M1344 IOGEAR, the IOGEAR logo, are trademark
3435Customer’s RecordThe model number and serial number of this product can be found on the product package. You should note this serial number in th
PART NO. M1344© 2009 IOGEAR®FUNIOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our h
45Package Content1 x Solar Power Bluetooth Hands-free Car Kit1 x USB Car Charger1 x USB Charging Cable1 x Windshield Mount4 x Suction Cups1 x Sun-Viso
45RequirementsYour mobile/cellular phone, PDA, or Smart Phone must be Bluetooth enabled and supports either Headset or Hands-free prole in order to w
67Device OverviewVolume Up1. Multi-function button 2. (MFB button) Volume Down3. Solar panel 4. Mute button5. USB charging port 6. MUTE1 3 4 5 62
67Charging Your Car KitMUTEBefore you begin using your Solar Power Bluetooth Hands-free Car kit, it is recommended to fully charge the device to ensu
89Using the car chargerPlug the micro-USB connection end of the USB charging cable to the Solar 1. Power Bluetooth Car Kit, and the other USB Type A c
Commentaires sur ces manuels